Painting Aluminum Trim - China

Painting aluminum trim coil at home and in workshop Painting aluminum trim coil at home and in workshop

“Painting aluminum trim coil” is often asked about since aluminum siding and trim has been applied in decoration of so many houses in the past years.

Learning about painting process in the workshop helps you to fully understand steps you should do at home to repair items made of trim aluminum coil.

Before getting an aluminum trim coil roll painted, manufacturers would first clean the roll surface completely, either in physical or chemical ways.

Sometimes mechanical equipment is necessary, too.

The purpose is to remove any materials that might prevent the following anodizing step from going on effectively.

A completely cleaned surface of aluminium coil will obtain a thick condense layer of anodizing film on the surface, but there will be micro holes on the surface, which should be concealed to make the film stronger and harder.

To paint the coil, pvdf, pe and pvc paints are all applicable.

These paints are divided into primers and finishing coats.

Multiple painting produces lasting color coated aluminum coil in severe natural conditions.

If you need to paint aluminum trim coil at home, the steps are similar in exception to the anodizing part.

You should first scrub the aluminum part to be painted with soapy water by combining 1 gallon of warm water and 1/4 cup of dish soap in a bucket.

Then then scrub down the entire aluminum surface to remove dirt and residue with the brush soaked with soapy water.

Wipe the aluminum with a clean, damp cloth, and if there are still residues on the aluminium surface, brush it again until it gets fully cleaned.

After the surface gets dry, you should begin your painting.

Now the point is, do you need a primer? If you want your paint work last as long as possible, the answer is yes, for a primer functions as a secondary protection line of the aluminium trim coil.

Make sure the primer you choose is safe for use on aluminum.

Do not move on the next step until the primer is dry.

Then dip a paintbrush into the paint, and brush the paint onto the aluminum using long, even strokes.

Never allow anyone touch the aluminium until the paint gets dry.

Painting coil stock on fascia?

Is it a viable solution to paint fascia covered w/ coil stock.

The paint on my fascia isn’t holding up at all.

Many of the boards are cracked/checked etc.

I back primed, end primed and used quality paint.

I’ve been considering covering the fascia with the pre bent coil stock ( I don’t have a break) which as far as I know only comes in white, and then painting it down the road if the bride can’t live with the color.

I wish I had used Azek or something similar but I really don’t want to tear down whats already done and start from scratch.

I guess a big part of the problem is that its a good sized job for one guy (my own place) and I get done a little here and a little there and now alot of the fascia looks like crap.

With the coil stock I figured I could get everything covered and come back and paint when everything else is done.

I don’t want to waste my time if this isn’t a good idea though.

Alll advice appreciated.

Can You Paint your Aluminium or Vinyl Trims?

Hello and welcome! I’m both deeply honoured and flattered you are considering using our painting services.

Since 1987 when I was at York University simply earning my way through school, I’ve had the privilege to meet and work with thousands of amazing homeowners like yourself.

Besides the birth of my daughter, there is nothing more satisfying than seeing a homeowner’s life change when we have transformed their dream home into a masterpiece.

For that reason, our painters take their jobs very seriously and are committed to our cause.

At Home Painters our mission is to paint homeowners’ dreams, and make your painting experience last a lifetime!

I look forward to hopefully meeting you one day, as it brings me tremendous joy to make homeowner’s dreams come true.

READ MORE ABOUT HOME PAINTERS TORONTO

Company Contact:

• Posted By: LITONG ALUMINUM INDUSTRY (Wuxi) CO., LTD

• Phone: 86-0755-82332214

• Address: Daliang Street, Shunde, foshan , guangdong , China

• Email:

• Website: https://www.alupaintcoil.com/

• Business Description: itongs painted aluminum business started in 1998 - It has four(4) large-scale aluminum coating plants spread throughout the four(4) major cities in China including Litong aluminum (Wuxi) Co.
  
  Ltd., Litong Aluminum (Guangdong) Co., Ltd., Litong Aluminum (Shanghai) Co., Ltd., Litong Aluminum (Shandong) Co., Ltd. A total of 26 coating lines can meet customers demands in different fields.
  
  aluminum with alloy 1XXX, 3XXX, 5XXX and 8XXX, thickness 0.022~1.5mm, width 20mm~1600mm can be coated.
  
  Annual capacity of painted aluminum coils/sheets/stripes are more than 100,000tons, which are exported to more than 100 countries and regions.
  
  Litongs painted aluminum coils/sheet/slats are widely used in construction, decoration, transportation, communication, food, medicine, lighting, home appliances, IT and many other fields.
  
  For example, aluminum shutters, aluminum Horizontal Blinds, aluminum flashings of roof window, aluminum gutters, aluminum ceilings, aluminum facades, aluminum roof, aluminum garden gates, etc.
  
  Litongs factories have gotten ISO9001 international quality system certificate and ISO14000 international environmental system certificate.
  
  In the past 20 years, Litongs Painted aluminum got global reputation due to our stable & good quality.
  
  Now, it grew up as a professional aluminum coating enterprise and the leader of aluminum coating industry in China.