Corrugated Pipe Culvert China Suppliers - China

Corrugation 68mm x 13mm Spiral Corrugated Pipe Corrugated Pipe Culvert China Suppliers

Characteristic of galvanized steel helical Corrugated Pipe Culvert

Specification

Pipe diameter: 300-2500mm

Length: 1-12m

Thickness: 1.6-3.2mm

High strength

It with more than 1.5 times compression strength than the concrete pipe because of the corrugation structure

Easy for transport

The weight of the corrugated steel pipe is only 1/10~1/5 of same size concrete pipe, even can be carried by people without machine.

Install in shorter time

The steel corrugated culvert is connect by clamping band or flange, and the length can be make according to the customers’ request, then easy to install, and can be installed in shorter time.

Long service life:

The steel corrugated culvert pipe adopt 300-600g/m2 galvanization steel plate, normally its servise life is 50-100 years, if in the strong corrosion environment, painting asphalt on the in and out surface of the pipe, can enlong 20-50 years based on the normal service life.

Economic

The standard length is 6m, simple connection, shorter working time.

Because it is light, easy for transport, with few foundation construction, lower fee on drain pipe.

For example, we make comparison on steel corrugated culvert pipe and concrete pipe in diameter 800mm, corrugated steel culvert pipe is only need about 90% if concrete pipe fee, and it can save cost of forklift, crane, and other machines when the transport is not good.

Cross section shape and size of galvanized steel helical corrugated culvert pipe

Normally, the cross section is round shape, corrugation is 68X13mm, 125X25mm

Application of helical corrugated steel culvert pipe

The helical corrugated steel culvert pipe is used in municipal drainage, building outside drainage, farm drainage, industry drain system, also adopt in road and railway closed conduit or culvert, shell of vertical pile, rain water collection, etc

Drainage: domestic sewage, golf course drain, underground garage, factory drain, factory, airport water drain.

Culvert: drain-pipe under the road, higher cross drain-pipe, underground culvert of railway, small tunnel, closed conduit, small bridge.

Protection shell: underground communication cable, protection pipe for gas pipe, also can be adopted on construction site, and protection shed, etc

Industry: air conduit for gas in coal mine (negative pressure)

Farm: driven well wall for farm, invert siphon for irrigation, farm water drain.

Structure

Corrugated culvert pipe is treatment by galvanized steel belt spiral seaming joint

The diameter is smaller than 1m, adopt corrugation 68X13mm, each section standard length is 6m, diameter is bigger than 1m, adopt corrugation 125X25mm, each section standard length is 6m, and can make difference size as per clients’ request±±±±

Corrugated culvert pipe connection by two or more pieces of clamping band or flange, inlay PE plate or sealant or rubber gasket, fasten by high strength bolts.

Material

The steel plate is DX52D or SGHC, chemical and mechanical property should be accord with EN10327 or JIS G 3302-2010, steel plate size tolerance should be accord with GB/T-709

Clamping band and angle steel material is Q235, chemical and mechanical property should be accord with GB/T700

Clamping band or angle steel fastener need to adopt high strength bolts, nuts, the grand should be or higher than 8.8, its property should be accord with GB/T1231

Corrugated pipe adopt hot galvanized steel belt for forming, or after forming then hot galvanization treatment.

Appearance

Clean, smooth, and the zinc coating uniformity.

Clamping band request

Connect pipe sections by clamping band, keep the pipe sections point at pipe sections, prevent separate, the bottom permeate or the filling back material permeate.

Drawing 3 classic clamping band system

When assemble the clamping band, lap over connect to each pipe section equally.

When fastening, the length and width of the part which over lap to the pipe have to can bearing the tightening force.

When assemble the clamp band, make sure the gap between two pipe section can be more than 25mm.

Clamp band width is 440mm

(remarks: normally, the clamp band is two pieces, for the big diameter, maybe need 3 pieces or more)

Angle steel connection request

Angle steel adopt Q235 steel

Flange is made by bending the angle steel, manual electric-arc welding and drilling holes.

Corrugated pipe welding angle steel flange adopt manual electric-arc welding.

Corrugated pipe both end welding flange.

Inner diameter is 1m or smaller than 1m, the pipe flange edge is in length 56mm, thickness 6mm equal-sided angle steel, other flange adopt in edge length 70mm, thickness 6mm equal-sided angle steel, for the big pressure, adopte width 70mm, thickness 6mm flat steel.

Company Contact:

• Posted By: Hengshui Yitong Pipe Industry Co.,Ltd.

• Phone: +86-318-5876998

• Address: Guangchuan Industrial Zone, Hengshui City, Hebei Province,China., Hengshui , Hebei , China

• Email:

• Website: https://www.corrugatedmetalculvert.com

• Business Description: Hengshui Yitong Pipe Industry Co., Ltd. is professional corrugated culvert pipes manufacturer, was founded in 1998, 600 employees.
  
  After 14 years of growth, Hengshui Yitong Pipe Industry Co., Ltd. became the most comprehensive leading corrugated culvert pipes manufacturer.
  
  We have more than 30 patents, and are the member unit joined to formulate the state standard, .
  
  Our main products include 4 types culvert pipes and irregular-shaped pipes, annual capacity is 500, 000 meters, the company obtained ISO9000 quality and ISO 14000 certificates, we can produce American and European standard products according to the customers' requirements.
  
  As a leading company in corrugated culverts pipes manufacturing, we focus on providing professional service and prompt lead time, producing quality products at competitive price.